Osavalmistuksen kustannustehokkuuden arviointi
Pitkälä, Juho Herman (2006)
Diplomityö
Pitkälä, Juho Herman
2006
Julkaisun pysyvä osoite on
https://urn.fi/URN:NBN:fi-fe20061425
https://urn.fi/URN:NBN:fi-fe20061425
Tiivistelmä
Tämän diplomityön tarkoituksena oli selvittää osavalmistuksen
kustannustehokkuutta Ruukki Engineering Seinäjoen palvelukeskuksessa.
Osavalmistuksessa osia leikataan, särmätään ja viimeistellään
kokoonpanohitsaukseen soveltuviksi komponenteiksi.
Kustannustehokkuuden selvittämisessä käytettiin aikaan perustuvia
mittausmenetelmiä, joiden pohjalta laskettiin tuotteen toteutuneita
kustannuksia. Toteutuneita kustannuksia verrattiin hinnoittelutaulukoihin.
Vertailussa havaittiin, että kaikkia työvaiheita ei ollut hinnoiteltu lainkaan.
Erot hinnoittelun ja toteutuneiden kustannusten välillä olivat merkittäviä.
Työssä tutkittiin myös jalostavan ajan osuutta kokonaisläpäisyajasta.
Mitattuja tietoja verrattiin kahteen aikaisemmin tehtyyn tutkimukseen.
Osavalmistuksessa aikaa kuluu paljon välivarastoissa ja työvaiheiden
läpäisyajat olivat joidenkin työvaiheiden kohdalla pitkiä. Diplomityön
tulokset olivat vertailukelpoisia muiden tutkimustenkanssa ja olivat ennalta
asetettujen hypoteesien mukaisia. The purpose of this thesis was clarifying the cost efficiency of the parts
manufacture at Ruukki Engineering Seinäjoki service center. In the parts
manufacture, the pieces are cut, bent, and finished into components that
are ready for the assembly welding.
In clarifying the cost efficiency, measurement methods based on time were
used, with which the actual costs were calculated. The actual costs were
compared to pricing charts. The comparison showed that some work
phases were not priced at all. Differences between the priced costs and
actual costs were significant.
The process time as a part of the total lead time was alsostudied in the
thesis. The measured results were compared to research carried out
earlier. During parts manufacture, lot of time was used in intermediate
storages and the lead time of some work phases were long. The results of
this thesis are comparable with other like research and they are in
accordance with preset hypothesis.
kustannustehokkuutta Ruukki Engineering Seinäjoen palvelukeskuksessa.
Osavalmistuksessa osia leikataan, särmätään ja viimeistellään
kokoonpanohitsaukseen soveltuviksi komponenteiksi.
Kustannustehokkuuden selvittämisessä käytettiin aikaan perustuvia
mittausmenetelmiä, joiden pohjalta laskettiin tuotteen toteutuneita
kustannuksia. Toteutuneita kustannuksia verrattiin hinnoittelutaulukoihin.
Vertailussa havaittiin, että kaikkia työvaiheita ei ollut hinnoiteltu lainkaan.
Erot hinnoittelun ja toteutuneiden kustannusten välillä olivat merkittäviä.
Työssä tutkittiin myös jalostavan ajan osuutta kokonaisläpäisyajasta.
Mitattuja tietoja verrattiin kahteen aikaisemmin tehtyyn tutkimukseen.
Osavalmistuksessa aikaa kuluu paljon välivarastoissa ja työvaiheiden
läpäisyajat olivat joidenkin työvaiheiden kohdalla pitkiä. Diplomityön
tulokset olivat vertailukelpoisia muiden tutkimustenkanssa ja olivat ennalta
asetettujen hypoteesien mukaisia.
manufacture at Ruukki Engineering Seinäjoki service center. In the parts
manufacture, the pieces are cut, bent, and finished into components that
are ready for the assembly welding.
In clarifying the cost efficiency, measurement methods based on time were
used, with which the actual costs were calculated. The actual costs were
compared to pricing charts. The comparison showed that some work
phases were not priced at all. Differences between the priced costs and
actual costs were significant.
The process time as a part of the total lead time was alsostudied in the
thesis. The measured results were compared to research carried out
earlier. During parts manufacture, lot of time was used in intermediate
storages and the lead time of some work phases were long. The results of
this thesis are comparable with other like research and they are in
accordance with preset hypothesis.