Hyppää sisältöön
    • Suomeksi
    • På svenska
    • In English
  • Suomeksi
  • In English
  • Kirjaudu
Näytä aineisto 
  •   Etusivu
  • LUTPub
  • Tieteelliset julkaisut
  • Näytä aineisto
  •   Etusivu
  • LUTPub
  • Tieteelliset julkaisut
  • Näytä aineisto
JavaScript is disabled for your browser. Some features of this site may not work without it.

Numerical analysis of working fluids for large scale centrifugal compressor driven cascade heat pumps upgrading waste heat

Uusitalo, Antti; Turunen-Saaresti, Teemu; Honkatukia, Juha; Tiainen, Jonna; Jaatinen-Värri, Ahti (2020-05-14)

Katso/Avaa
uusitalo_et_al_numerical_analysis_of_working_fluids_final_draft.pdf (2.955Mb)
Lataukset: 


Post-print / Final draft

Uusitalo, Antti
Turunen-Saaresti, Teemu
Honkatukia, Juha
Tiainen, Jonna
Jaatinen-Värri, Ahti
14.05.2020

Applied Energy

269

Elsevier

School of Energy Systems

https://doi.org/10.1016/j.apenergy.2020.115056
Näytä kaikki kuvailutiedot
Julkaisun pysyvä osoite on
https://urn.fi/URN:NBN:fi-fe2020062345371

Tiivistelmä

Heat pump technology has the capability to upgrade unusable low-temperature waste heat and make the upgraded heat usable for different types of industrial and domestic heating applications. Heat upgrading could allow to reach significant energy savings and reduced emissions when compared to other heat production methods. In this paper, upgrading waste heat into a higher temperature with large-scale centrifugal compressor driven cascade heat pumps was studied numerically. A combined method for heat pump thermodynamic analysis and compressor design analysis was developed and implemented in order to investigate the effect of different working fluid combinations and the effect of the cascade heat exchanger temperature level on the heat pump performance. Seven potential fluid candidates were included and condenser temperature of 90 °C, evaporator temperature of 20 °C, and evaporator heat rate of 1 MW were used in the analysis. It was concluded, that the implemented method can provide an efficient tool for evaluating suitable working fluids and design operating conditions for centrifugal compressor driven high temperature cascade heat pumps. The highest coefficient of performance of 3.08 was simulated by using R601 as the fluid in the low-temperature cycle and R245fa in the high-temperature cycle. These fluids also resulted in feasible compressor geometries and rotational speeds, as well as allowed to reach high compressor efficiencies of well above 80% based on the enthalpy loss models. Coefficient of performances of over 3.0 were simulated also with the fluid combinations R601/R600, R245fa/R245fa and R600/R245fa.

Lähdeviite

Uusitalo, A., Turunen-Saaresti, T., Honkatukia, J., Tiainen, J., Jaatinen-Värri, A. (2020). Numerical analysis of working fluids for large scale centrifugal compressor driven cascade heat pumps upgrading waste heat. Applied Energy, vol. 269. DOI: 10.1016/j.apenergy.2020.115056

Alkuperäinen verkko-osoite

https://www.sciencedirect.com/science/article/pii/S0306261920305687?via%3Dihub
Kokoelmat
  • Tieteelliset julkaisut [1560]
LUT-yliopisto
PL 20
53851 Lappeenranta
Ota yhteyttä | Tietosuoja | Saavutettavuusseloste
 

 

Tämä kokoelma

JulkaisuajatTekijätNimekkeetKoulutusohjelmaAvainsanatSyöttöajatYhteisöt ja kokoelmat

Omat tiedot

Kirjaudu sisäänRekisteröidy
LUT-yliopisto
PL 20
53851 Lappeenranta
Ota yhteyttä | Tietosuoja | Saavutettavuusseloste