Hyppää sisältöön
    • Suomeksi
    • På svenska
    • In English
  • Suomeksi
  • In English
  • Kirjaudu
Näytä aineisto 
  •   Etusivu
  • LUTPub
  • Tieteelliset julkaisut
  • Näytä aineisto
  •   Etusivu
  • LUTPub
  • Tieteelliset julkaisut
  • Näytä aineisto
JavaScript is disabled for your browser. Some features of this site may not work without it.

Finite element simulation of welding distortions in ultra-high strength steel S960 MC including comprehensive thermal and solid-state phase transformation models

Ghafouri, Mehran; Ahn, Joseph; Mourujärvi, Juho; Björk, Timo; Larkiola, Jari (2020-06-17)

Katso/Avaa
ghafouri_et_al_finite_element_structure_aam.pdf (2.387Mb)
Lataukset: 


Post-print / Final draft

Ghafouri, Mehran
Ahn, Joseph
Mourujärvi, Juho
Björk, Timo
Larkiola, Jari
17.06.2020

Engineering Structures

219

Elsevier

School of Business and Management

https://doi.org/10.1016/j.engstruct.2020.110804
Näytä kaikki kuvailutiedot
Julkaisun pysyvä osoite on
https://urn.fi/URN:NBN:fi-fe2020100678160

Tiivistelmä

The objective of this study is developing a thermo-metallurgical-mechanical finite element (FE) model incorporating the effect of solid-state phase transformation (SSPT) to accurately simulate deformations for single bead-on-plate welding of an ultra-high strength carbon steel. Comprehensive phase transformation modeling including both diffusive and diffusionless (displacive) transformation kinetics, was performed and the effect of SSPT on welding-induced deformations was investigated. Modelling the heat source and thermal boundary conditions were accomplished in the ABAQUS user subroutines, the former based on the Goldak’s double ellipsoidal heat source model. An ABAQUS user subroutine was developed in which kinetics of diffusive and diffusionless transformations based on Machnienko model and Koistinen-Marburger formula, respectively, were implemented. Modification of strains due to volumetric change as a result of SSPT was accomplished using an ABAQUS user-defined subroutine. A comparison between the temperature histories from thermal simulations (with isotropic as well as anisotropic conductivities) and measurement with thermocouples shows that much better verification with experiments can be obtained when anisotropic conductivity is applied. From the results of the mechanical simulations (with and without considering the effect of SSPT) and comparison with measured deformations, it is observable that more accurate prediction of welding-induced angular and bending distortions is possible when the effect of SSPT is incorporated for the material under investigation.

Lähdeviite

Ghafouri, M., Ahn, J., Mourujärvi, J., Björk, T., Larkiola, J. (2020). Finite element simulation of welding distortions in ultra-high strength steel S960 MC including comprehensive thermal and solid-state phase transformation models. Engineering Structures, vol. 219. DOI: 10.1016/j.engstruct.2020.110804

Alkuperäinen verkko-osoite

https://www.sciencedirect.com/science/article/pii/S014102961934800X?via%3Dihub
Kokoelmat
  • Tieteelliset julkaisut [1103]
LUT-yliopisto
PL 20
53851 Lappeenranta
Ota yhteyttä | Tietosuoja | Saavutettavuusseloste
 

 

Tämä kokoelma

JulkaisuajatTekijätNimekkeetKoulutusohjelmaAvainsanatSyöttöajatYhteisöt ja kokoelmat

Omat tiedot

Kirjaudu sisäänRekisteröidy
LUT-yliopisto
PL 20
53851 Lappeenranta
Ota yhteyttä | Tietosuoja | Saavutettavuusseloste