Hyppää sisältöön
    • Suomeksi
    • På svenska
    • In English
  • Suomeksi
  • In English
  • Kirjaudu
Näytä aineisto 
  •   Etusivu
  • LUTPub
  • Diplomityöt ja Pro gradu -tutkielmat
  • Näytä aineisto
  •   Etusivu
  • LUTPub
  • Diplomityöt ja Pro gradu -tutkielmat
  • Näytä aineisto
JavaScript is disabled for your browser. Some features of this site may not work without it.

Applicability of adsorption kinetic and isotherm models for cadmium removal using nanocellulose–clay–chitosan composites

Raza, Ali (2026)

Katso/Avaa
Mastersthesis_Raza_Ali.pdf (1.322Mb)
Lataukset: 


Diplomityö

Raza, Ali
2026

School of Engineering Science, Kemiantekniikka

Kaikki oikeudet pidätetään.
Näytä kaikki kuvailutiedot
Julkaisun pysyvä osoite on
https://urn.fi/URN:NBN:fi-fe20261021135675

Tiivistelmä

The pollution of water by cadmium is of great concern, due to the toxicity, persistence and the tendency of Cd(II) to be released into water and not be easily removed. Adsorption is a treatment technique that is studied extensively, as it is easy and flexible, and can be implemented with low cost or bio materials. This thesis evaluated how suitably adsorption kinetic and isotherm models describe Cd(II) removal using a nanocrystalline cellulose–clay–chitosan composite. The primary goal was to investigate whether the adsorption ability is influenced by the variation in clay type and interpretation and possible adsorption mechanisms of the models.

The preparation of three composites with nanocrystalline cellulose and chitosan as well as three different clays, namely bentonite, kaolin and green clay were done. All materials were synthesized by the same method so that the results of the comparison would be more reliable. Batch adsorption experiments examined the effects of initial Cd(II) concentration, solution pH and contact time. The efficiency of adsorption process was assessed for removal percentage and adsorption capacity whereas literature search was used to validate the interpretation of the adsorption kinetic and isotherm modelling. The functional groups and mineral bands of the prepared composite was gathered using FTIR.

The results showed that all three composites could successfully remove Cd(II) from the aqueous solution; however, the removal behaviors of these three composites were different and the amount of removal was related to the clay type. The kaolin composite exhibited the most consistent stability in the first concentration study and had a good adsorption capacity under higher concentration of Cd(II). Bentonite composite was effective under alkaline condition with the greatest removal at pH 9 while good removal by green clay composite was observed under mild acidic condition and there was a slow initial rate of adsorption in the kinetic run. Results on contact time indicated very fast uptake of Cadmium (Cd(II)) initially followed by gradual approach towards near-equilibrium. In the FTIR spectra, the –OH, –NH, C–O, Si–O and Clay related bands were observed, which is consistent with the formation of the NCC–clay–chitosan composite.

Overall, the study reveals that overall clay type affects the Cd(II) adsorption behaviour and should be taken account when analyzing the results of kinetic and isotherm studies. Another conclusion is that models were applied to describe adsorption process should not be interpreted without experimental trends or material characterizations.
Kokoelmat
  • Diplomityöt ja Pro gradu -tutkielmat [15783]
LUT-yliopisto
PL 20
53851 Lappeenranta
Ota yhteyttä | Tietosuoja | Saavutettavuusseloste
 

 

Tämä kokoelma

JulkaisuajatTekijätNimekkeetKoulutusohjelmaAvainsanatSyöttöajatYhteisöt ja kokoelmat

Omat tiedot

Kirjaudu sisäänRekisteröidy
LUT-yliopisto
PL 20
53851 Lappeenranta
Ota yhteyttä | Tietosuoja | Saavutettavuusseloste