Modernisation of bar mill automation
Kaartinen, Seppo (2006)
Tiivistelmä
Työn tavoitteena on tankovalssaamon perusautomaation modernisointi Ovako Bar Oy Ab:n Imatran terästehtaalla. Vanha automaatiojärjestelmä on toteutettu 80-luvun puoli-välin tekniikalla käyttämällä Siemens Sicomp MMC 216 moniprosessori-tietokonetta, Siemens Simatic S5 logiikkayksiköitä sekä Siemens Simadyn D DC-käyttöjä.
Modernisoinnin tarkoituksena on korvata vanha automaatiojärjestelmä Siemens PCS7 -järjestelmällä siten, että tankovalssaamon automaatiojärjestelmä voidaan liittää osaksi jo aiemmin modernisoituja, nykyisin PCS7 automaatiojärjestelmällä toteutettuja ratkaisu-ja. Valssaamon mekaniikka ei mahdollista tuotannon kasvattamista pelkästään uuden automaatiojärjestelmän avulla, joten modernisointi keskittyy parantamaan järjestelmän luotettavuutta ja helpottamaan ylläpitoa.
Projekti päätettiin jakaa kolmeen osaan, jotka voidaan toteuttaa erillisinä osaprojekteina. Tärkein osaprojekti on MMC järjestelmän uusinta. Muut osaprojektit ovat DC-käyttöjen sekä ohjelmoitavien logiikkojen modernisointi. Osaprojektit valittiin siten, että mikä tahansa niistä voidaan toteuttaaerillisenä projektinaan, mikäli kaikkia osia ei voida mo-dernisoida samanaikaisesti budjetin asettamien rajoitusten vuoksi. The aim of this thesis is to make an inquiry for mill automation modernisation in Ovako Bar Oy Ab Imatra bar mill. The old automation system is based on the technology of the mid 80's Siemens MMC 216 multi microcomputer, Siemens Simatic S5 PLC-units and Siemens Simadyn D DC-drives.
The aim is to revamp thebar mill basic automation using Siemens PCS7 automation platform so that the bar mill automation system can be integrated as part of the already existing level1 automation. The mechanical design of the mill does not enable im-provement ofthe mill production by means of the automation system. Therefore the aim of therevamping is concentrated on the improvement of the mill availability and main-tainability.
The revamping project was decided be divided into three stages. The replacement of the MMC-system is the main stage. The additional stages are revamping of the DC-drives and PLC-units. These stages were selected so that any of them can be carried out as individual projects, in case the entire revamping project can not be carried out at once due to limitations set bythe budget.
Modernisoinnin tarkoituksena on korvata vanha automaatiojärjestelmä Siemens PCS7 -järjestelmällä siten, että tankovalssaamon automaatiojärjestelmä voidaan liittää osaksi jo aiemmin modernisoituja, nykyisin PCS7 automaatiojärjestelmällä toteutettuja ratkaisu-ja. Valssaamon mekaniikka ei mahdollista tuotannon kasvattamista pelkästään uuden automaatiojärjestelmän avulla, joten modernisointi keskittyy parantamaan järjestelmän luotettavuutta ja helpottamaan ylläpitoa.
Projekti päätettiin jakaa kolmeen osaan, jotka voidaan toteuttaa erillisinä osaprojekteina. Tärkein osaprojekti on MMC järjestelmän uusinta. Muut osaprojektit ovat DC-käyttöjen sekä ohjelmoitavien logiikkojen modernisointi. Osaprojektit valittiin siten, että mikä tahansa niistä voidaan toteuttaaerillisenä projektinaan, mikäli kaikkia osia ei voida mo-dernisoida samanaikaisesti budjetin asettamien rajoitusten vuoksi.
The aim is to revamp thebar mill basic automation using Siemens PCS7 automation platform so that the bar mill automation system can be integrated as part of the already existing level1 automation. The mechanical design of the mill does not enable im-provement ofthe mill production by means of the automation system. Therefore the aim of therevamping is concentrated on the improvement of the mill availability and main-tainability.
The revamping project was decided be divided into three stages. The replacement of the MMC-system is the main stage. The additional stages are revamping of the DC-drives and PLC-units. These stages were selected so that any of them can be carried out as individual projects, in case the entire revamping project can not be carried out at once due to limitations set bythe budget.